If you're looking for the best PrusaSlicer PLA settings for your Dremel 3D20 printer, this profile delivers optimized configurations designed specifically for the Micro Swiss all metal hot end and 0.6mm hardened nozzle. Built around Sunlu High Speed Matte Black PLA, these PrusaSlicer settings prioritize surface finish and strength over raw speed, ensuring reliable prints with excellent dimensional accuracy and durability. Whether you're printing functional parts or detailed models, this profile balances quality and reliability for consistent results.
This PrusaSlicer PLA configuration is tuned for the unique characteristics of the Dremel 3D20 with its upgraded Micro Swiss hot end. The 0.6mm hardened nozzle allows for thicker extrusion widths, which improves strength while maintaining clean surface finishes when paired with appropriate cooling and wall strategies. The profile uses four perimeters to build robust outer walls, combined with strategic infill density and solid layer counts that maximize part strength without excessive print time. Cooling is carefully managed to prevent warping while ensuring proper layer adhesion, and travel speeds are optimized to reduce stringing on this printer's motion system.
Perimeters and Wall Structure: This profile uses four perimeters to create thick, strong outer walls. Combined with nine top solid layers and seven bottom solid layers, this ensures parts have excellent structural integrity and smooth surfaces. The external perimeter speed is set conservatively at 30mm/s to prioritize surface quality.
Layer Height and Extrusion Width: A 0.3mm layer height balances detail with print speed, while the 0.66mm extrusion width takes advantage of the 0.6mm nozzle to create strong, consistent lines. The first layer uses slightly wider extrusion (0.7mm) for improved bed adhesion.
Temperature and Cooling: The nozzle temperature is set to 210°C with a bed temperature of 55°C, appropriate for Sunlu PLA. Cooling is enabled from layer four onward, with fan speeds ramping to 100% for overhangs. This prevents sagging while maintaining layer bonding.
Infill and Density: A 20% grid infill pattern provides adequate internal support without excessive material use. The infill speed of 60mm/s is faster than perimeter speeds, optimizing print time while maintaining part strength.
Retraction Settings: Minimal retraction (1mm at 35mm/s) reduces stringing while avoiding unnecessary wear on the filament drive. The retract lift is disabled to prevent z-axis artifacts.
Why are there so many perimeters in this profile? Four perimeters create thick, durable walls that resist impact and stress. This is especially important for functional parts and assemblies where strength matters more than speed. The 0.6mm nozzle makes this practical without excessive print time.
Can I print faster with these settings? This profile prioritizes surface finish and strength over speed. If you need faster prints, you can increase perimeter and infill speeds by 10-15mm/s, but expect slightly reduced surface quality and part durability. Test on non-critical parts first.
What bed temperature should I use? The profile uses 55°C for Sunlu PLA, which works well for the Dremel 3D20. If you experience bed adhesion issues, try 60°C. If prints warp, reduce to 50°C and ensure your bed is clean and level.
Is this profile compatible with other PLA brands? Yes, most standard PLA filaments work well with these settings. However, some brands may require slight nozzle temperature adjustments (±5°C). Start with the profile as-is and adjust only if you see extrusion issues or poor layer adhesion.
Why is the first layer speed set to 30%? Slower first layer speeds ensure proper bed adhesion and a clean foundation for the rest of the print. This is especially important on the Dremel 3D20, where a solid first layer prevents warping and improves overall print reliability.
Load this profile into PrusaSlicer and test it on a small part first. Monitor the first layer closely to ensure proper adhesion, and check that the nozzle is clean and the bed is level. If you notice any issues with surface quality or adhesion, make small adjustments to temperature or bed leveling rather than changing multiple settings at once. This profile is designed to work reliably with the Dremel 3D20 and Sunlu PLA, but every printer has minor variations that may require fine-tuning.
For additional profiles and community-tested configurations, SliceFoundry offers a growing library of optimized slicer settings for various printer and filament combinations. Whether you're refining this profile or exploring alternatives, having access to tested configurations can save time and reduce failed prints.
```The best way to test a slicer profile is with the right model. Check out jinx logo - a great match for PLA and a solid way to dial in these settings straight out of the box.